新型电阻点焊机恒流模糊控制器的研制

介绍了一种新型电阻点焊机恒流模糊控制器 ,对系统的硬件和原理算法、功能及工作原理和试验结果等方面作了较详细的阐述。该控制器采用单片微机控制电焊机实现闭环恒流效果 ,其控制精度为 2 % ,并具有完善的故障自诊断、自适应和保护功能     

VCO电调特性的线性校正技术综述

VCO电调特性的线性校正技术是决定线性调频连续波雷达系统性能的关键技术之一。给出了VCO电调线性度的基本定义。VCO电调特性的线性校正技术主要包括电抗补偿线性校正、开环线性校正和闭环线性校正三种基本校正方案。详细分析了各种校正方案的基本原理,并对各种校正方案的优缺点进行了对比分析;同时,详细介绍了VCO线性校正技术的最新研究进展。     

一种电流反馈型三相无刷直流电机控制器

基于经典的闭环反馈控制理论和PWM理论在电机控制中的应用,设计了一种三相无刷直流电机控制器.该电路可实现对三相无刷直流电机的驱动和控制,具有功率电压高、驱动电流大、零点精确等优点,同时具有高边占空比100％可调和过流保护等功能,是一款真正的四象限扭矩电机控制器.     

Direct and two-step methods for closed-loop identification: a comparison of asymptotic and finite data set performance

The asymptotic and finite data behavior of some closed-loop identification methods are investigated. It is shown that, when the output power is limited, closed-loop identification can generally identify models with smaller variance than open-loop identification. Several variations on some two-step identification methods are compared with the direct identification method. High order FIR models are used as process models to avoid bias issues arising from inadequate model structures for the processes. Comparisons are, therefore, made based on the variance of the identified process models both for asymptotic situations and for finite data sets. Process model bias resulting from improper selection of the noise and sensitivity function models is also investigated. In this context, the results support the use of direct identification methods on closed-loop data.     

基于闭环控制策略的负载谐振型臭氧发生器电源

介质阻挡放电型臭氧发生器负载呈容性,随负载外加电压的升高,间隙放电逐渐增强,其总的负载等效电容逐渐变大。针对负载的这一特点,提出了一种基于逆变器输出电流进行闭环频率跟踪控制的高频逆变电源方案,详细分析了该控制策略的特点,并研制了实验样机,进行了实验验证,得出应用该方案的电源具有结构简单、工作频率变化范围小、系统参数容易选择、可靠性高等优点。     

微细超声加工机床运动控制系统设计

微细超声加工机床设计包括硬件设计与运动控制系统设计,运动控制系统是机床的核心组成部分,直接或者间接地影响到加工质量与加工效率。采用宏微复合的硬件设计结构能有效地保证运动控制精度,针对精密微三维运动平台,基于LabVIEW开发了微细超声加工中的运动控制系统,该系统包括初始化模块、粗对刀模块、精确对刀模块、绝对坐标实时显示模块、数据采集模块与加工模块。将微细工具所受的实时力与微三维运动平台的运动结合形成闭环控制,能有效地实现精确对刀以及恒压力进给加工。最后,对控制系统进行了测试,研究了恒力控制范围与增量位移、进给速度、回退速度之间的关系。     

Experimental Research on Parallel Conversion Control of Drying Temperature in a Closed-Loop Heat Pump Dryer

The paper proposes a method to handle the challenge of temperature control in a closed-loop heat pump dryer that can operate both in heating cycle and refrigeration cycle. It is hard to avoid the violent fluctuations of drying temperature as the operation mode changes. Hence, the parallel conversion control is introduced to realize the accurate control of drying temperature. The main idea of the controller design lies in the use of different membership functions and fuzzy control rules for the two operation modes. Experimental results show that the temperature fluctuations are reduced when using parallel conversion control with fast and stable response as compared to the fixed-frequency and PID control system. One of the parameters, R _f , representing the value of undershoot ratio is 0.4, 0.48, and 0.64 when drying temperature is fixed at 30, 35, and 38°C, respectively, with a parallel conversion controller. In order to study the application prospects of the parallel conversion control system, a comparison experiment with different compressor frequency ranges was also conducted.     

基于“多表合一”系统的智能表异常诊断及处理方法研究

文章在分析电、水、气智能表计故障诊断和实际消缺工作流程特点的基础上,提出了一种基于"多表合一"系统的智能表异常诊断和处理方法,该方法首先通过关联挖掘获取诊断规则,然后将监测的数据转换为事件元并进行规则匹配以获取诊断结果,最后通过现场排查确认并反馈诊断结果。该方法将异常诊断和消缺闭环管理结合起来,通过对诊断知识库的不断完善来提高异常诊断的准确性,充分发挥关联挖掘技术的优越性。     

纱线张力检测与控制技术的研究现状与展望

总结纱线张力检测与控制技术的研究现状及发展趋势.阐述了纱线"三辊式"张力检测的原理,对当前国内外有关接触式和非接触式纱线张力检测及控制原理的研究状况进行调研与分析.指出:当前纱线张力检测和控制技术的研究主要方向为采用非接触方式动态测试纱线张力并采取自适应控制技术,以使纱线的张力保持恒定.研究主要集中在提高测试系统的精度、性能、使用方便性及环境适应性上.其发展的总趋势是拓展测量范围,提高检测精度和可靠性;采用闭环控制技术,实现恒张力控制;采用微机电技术,实现在线非接触式检测与控制.     

轻型汽车整体式驱动桥柔性组装生产线设计方案

通过对轻型汽车整体式驱动桥产品组装工艺流程进行分析,合理布置各组装线顺畅衔接形式,达到了在线检测、标准化组装、非同步积放式输送、多种类产品共线一个流柔性生产模式的要求。